crank case breather mod -- question...
#1
crank case breather mod -- question...
I want to do the crank case breather mod that I hear some of you guys talking about, but how in the world do you reach the port on the air cleaner box with your drill???
It looks like I need a really long flexible drill bit to reach that hole! *LOL* Am I missing something here? Do I have to take the exhaust header off???
Please advise...
It looks like I need a really long flexible drill bit to reach that hole! *LOL* Am I missing something here? Do I have to take the exhaust header off???
Please advise...
#2
RE: crank case breather mod -- question...
ORIGINAL: NavKLX
I want to do the crank case breather mod that I hear some of you guys talking about, but how in the world do you reach the port on the air cleaner box with your drill???
It looks like I need a really long flexible drill bit to reach that hole! *LOL* Am I missing something here? Do I have to take the exhaust header off???
Please advise...
I want to do the crank case breather mod that I hear some of you guys talking about, but how in the world do you reach the port on the air cleaner box with your drill???
It looks like I need a really long flexible drill bit to reach that hole! *LOL* Am I missing something here? Do I have to take the exhaust header off???
Please advise...
Remove the hose from the front lower right side of the airbox. Insert the drill bit (not chucked in a drill, just by itself) and then use vice grips to turn it. It's very soft plastic and will only take you a few mins. to bore the hole out. Use your shop vac to get the pieces of plastic out of the airbox and then put the hose back on.
#5
RE: crank case breather mod -- question...
HI, so I am just about to get stuck in on the carb mods tonight but I think I am a bit lost on the crank case breather...? theres no drilling on the crankcase itself.... all that is needed is a new hole in the air boxto let the new hose through...? LOST!
any chance of a pointer...
newby to kawi 4 strokes!!
cheers
any chance of a pointer...
newby to kawi 4 strokes!!
cheers
#6
RE: crank case breather mod -- question...
You don't drill the crank case. Only drill the airbox where the breather hose goes in. It looks like there is a big hole that goes through the air box, but it steps down to a very small hole. Take a drill bit and heat it up with a propane torch and then just push the bit through. Quick and easy and no shavings. You will reuse the same breather hose.
#7
RE: crank case breather mod -- question...
follow the hose from the motor all the back to where it connects to the air box. it'll be on the brake pedal side of the bike. disconnect the hose from the air box.. the inside hole will be small than the outside. making the inside diameter larger is all there is to it. once you clean it all up reconnect the hose and your done.
#8
RE: crank case breather mod -- question...
Cheers for the heads up on that, there I was thinking that I had to get a seperate breather and re-route some new hose.....!
So, I use the dj kit for klx300 and the needle is set on slot #3 from the top down....what would be the advantage of moving the clip up one notch...? Only asking as I have read in another thread that someone had the same set up but on #2...?
many thanks.......carb is stil on the table!
So, I use the dj kit for klx300 and the needle is set on slot #3 from the top down....what would be the advantage of moving the clip up one notch...? Only asking as I have read in another thread that someone had the same set up but on #2...?
many thanks.......carb is stil on the table!
#9
RE: crank case breather mod -- question...
ORIGINAL: nosneb69
Cheers for the heads up on that, there I was thinking that I had to get a seperate breather and re-route some new hose.....!
So, I use the dj kit for klx300 and the needle is set on slot #3 from the top down....what would be the advantage of moving the clip up one notch...? Only asking as I have read in another thread that someone had the same set up but on #2...?
many thanks.......carb is stil on the table!
Cheers for the heads up on that, there I was thinking that I had to get a seperate breather and re-route some new hose.....!
So, I use the dj kit for klx300 and the needle is set on slot #3 from the top down....what would be the advantage of moving the clip up one notch...? Only asking as I have read in another thread that someone had the same set up but on #2...?
many thanks.......carb is stil on the table!
#10
RE: crank case breather mod -- question...
ORIGINAL: nosneb69
cheers
cheers